Troubleshooting Windows Blue Screen Of Death errors...

  • Filter
  • Time
  • Show
Clear All
new posts

    Troubleshooting Windows Blue Screen Of Death errors...

    When a serious system crash triggers a Stop error, better known as the Blue Screen Of Death.
    Interpreting/understanding the information displayed on the scary Blue Screen Of Death will
    accelerate your troubleshooting efforts.
    This article will help you in understanding the Most common "Blue Screen Of Death" Error Messages occuring in any version of Windows..

    STOP: 0x0000000A

    This Stop error, which can be caused by either software or hardware, indicates that a kernel-mode process or driver attempted to access a memory location it did not have permission to access or a memory location that exists at a kernel interrupt request level (IRQL) that was too high. A kernel-mode process can access other only processes that have an IRQL that's equal to or lower than its own.

    Troubleshooting a Stop 0x0000000A error in Windows

    STOP: 0x0000001E

    This Stop error indicates that indicates that the Windows kernel detected an illegal or unknown processor instruction. The problems that cause this Stop error can be either software or hardware related and result from invalid memory and access violations, which are intercepted by Windows' default error handler if error-handling routines are not present in the code itself.

    Possible Resolutions to STOP 0x0A, 0x01E, and 0x50 Errors

    STOP: 0x00000050

    This Stop error indicates that requested data was not in memory. The system generates an exception error when using a reference to an invalid system memory address. Defective memory (including main memory, L2 RAM cache, video RAM) or incompatible software (including remote control and antivirus software) might cause this Stop error.

    Possible Resolutions to STOP 0x0A, 0x01E, and 0x50 Errors

    STOP: 0x0000007B

    This Stop error indicates that Windows has lost access to the system partition or boot volume during the startup process. Installing incorrect device drivers when installing or upgrading storage adapter hardware typically causes this Stop error. This error could also indicate a possible virus infection.

    STOP Msg: 0x0000007B or "0x4,0,0,0 Error" during NT Setup

    STOP: 0x0000007F

    This Stop error indicates a hardware problem resulting from mismatched memory, defective memory, a malfunctioning CPU, or a fan failure that's causing overheating.

    General causes of "STOP 0x0000007F" errors

    STOP: 0x0000009F

    This Stop error indicates that a driver is in an inconsistent or invalid power state. This Stop error typically occurs during events that involve power state transitions, such as shutting down, or moving in or out of standby or hibernate mode.

    Troubleshooting a Stop 0x9F Error in Windows

    STOP: 0x000000D1

    This Stop error indicates that the system attempted to access pageable memory using a kernel process IRQL that was too high. The most typical cause is a bad device driver (one that uses improper addresses). It can also be caused by faulty or mismatched RAM or a damaged pagefile.

    Error Message with RAM Problems or Damaged Virtual Memory Manager

    STOP: 0x000000EA

    This Stop error indicates that a device driver problem is causing the system to pause indefinitely. Typically, this problem is caused by a display driver waiting for the video hardware to enter an idle state. This might indicate a hardware problem with the video adapter or a faulty video driver.

    Error message: STOP 0x000000EA THREAD_STUCK_IN_DEVICE_DRIVER

    STOP: 0x00000024

    This Stop error indicates that a problem occurred within Ntfs.sys, the driver file that allows the system to read and write to drives formatted with the NTFS file system. (A similar Stop message, 0x00000023, exists for the file allocation table [FAT16 or FAT32)] file systems.)

    Troubleshooting Stop 0x24 or NTFS_FILE_SYSTEM Error Messages

    STOP: 0xC0000218

    This Stop error indicates that a necessary registry hive file could not be loaded. The file may be corrupt or missing. The registry file may have been corrupted due to hard disk corruption or some other hardware problem. A driver may have corrupted the registry data while loading into memory or the memory where the registry is loading may have a parity error.

    How to Troubleshoot a Stop 0xC0000218 Error Message

    STOP: 0xC0000221

    This Stop message indicates driver, system file, or disk corruption problems (such as a damaged paging file). Faulty memory hardware can also cause this Stop message to appear.

    "STOP: C0000221 unknown hard error" or "STOP: C0000221
    STATUS_IMAGE_CHECKSUM_MISMATCH" error message occurs
    Rock _a.k.a._ Jack Daniel

    Follow eUKhost on Twitter || Join eUKhost Community on Facebook

    having this and cant able to fix


      i found the fix
      Driver Power State Failure – Fixing Solutions DRIVER_POWER_STATE_FAILURE, Stop: 0x0000009F, stop 9f or 0x0000009F whatever you call, it’s all are the BSOD error codes to define the problem by your …


        This problem occurs because of outdated drivers, corrupted system files, GUI errors, and sometimes faulty hardware. To fix this issue you can check this guide which I found on the internet and it is very helpful. Hope it may work for you as it is worked for me.
        Last edited by Chalresjames; 19-04-2021, 10:12.


          Hi, thanks for sharing this guide it's really ineterssent